Parts & Accessories
- Shell: 8mm flanged axle nut - Flanged
Don't let a bent or worn dust cap sully an otherwise well-functioning Shimano Alfine internally geared hub. Get a spare and replace as necessary for continued performance and to preserve the longevity that you expect from Alfine.
Keeping that well-functioning Shimano Alfine internally geared hub in top working condition means keeping the internals clean. Replace the left hub seal ring when necessary for continued performance and to preserve the longevity that you expect from Alfine.
Protect your tubes without adding bulk with these Rim Strips from FSA. They're lightweight, and come in different lengths according to wheel size. Peace-of-mind comes standard.
Need a Shift Cable Fixing Bolt Unit for your Alfine S7000/S700 hub? Here it is. Now, get that bike back on the road!
Do you need to replace the right lock washer seal on your Alfine SG-S700 internally geared hub? If you're not sure, it might not be a bad idea, as contamination from damaged or worn seals is the kryptonite of virtually maintenance-free internally geared hubs.
Replacement indicator chain for three speed Sturmey Archer hubs.
Keeping contamination out of your internally geared hub is critical to its function and longevity. Sometimes, the oil port bolt comes loose and it's easy to lose, even if you've just taken it out to oil your hub. Keep a spare or two so your hub stays clean inside and it'll last you many, many miles.
$5.95 - $8.95
Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up
This lightweight, high-pressure rim tape offers great protection against spoke hole flats and is easy to install. This Italian-made tape is light and thin, so it will not inhibit tire fitting. Nylon elastic material is used to ensure a snug fit without movement.
New cones make hubs spin like silk. Take advantage of your Shimano Alfine hub's highly serviceable design, and replace the bearing cones if they are worn or damaged. This one is specifically for the right side.
This outer receiver unit works with the CJ-S700 Cassette Joint Unit for Shimano Alfine SG-S700 internally geared hub. This part can become worn, cracked, or torn, exposing the shift cable and possibly other components to unwanted dirt, water, mud, you name it. You don't want that.
- High performance adhesive tape, a great pairing with Velox Cement - Each roll is usually adequate for gluing two tubular tires - Protects tube from spoke/nipple/rim puncture
If the bearings are getting rough on your Shimano Internally Geared hub, it could simply be a matter of replacing a pitted cone and repacking the bearing with grease. - Fits left side of Alfine SG-S700 hubs
Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech, Joy U, KK 9mm x 1, front hub - Compatible with 9mm x 1 axle - Cone Wrench Size: 15mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - JoyTech, Joy U, KK 9mm x 1, front hub - Taiwanese front hubs with 9mm x 1 axle
Don't let a cracked or worn dust cap sully an otherwise well-functioning Shimano Alfine internally geared hub. Get a spare and replace as necessary for continued performance and to preserve the longevity that you expect from Alfine.
$12.39 - $20.19
Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.
-Replacement left side cone and locknut for Shimano 105 FH-5800 rear hub
$13.50 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
$14.95 - $79.95
Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).
- Extra security against theft - 5mm hex CrMo axle
$15.29 - $26.69
- AL6061 alloy tubeless Presta valve - Includes 2 O-rings, one standard profile and one aero profile, for an airtight seal on any rim - Removable valve core for installing sealant - Additional replacement valve cores sold separately - Sold individually
Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S7000 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S7000-8
$16.00 - $19.99
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
On today's road forks, there are multiple front axle standards. Mavic front axle adapters allow you to mix and match without replacing wheels/forks. Most Mavic wheels can be fitted with specific adapters to match your fork end dimensions. - Converts Mavic road hubs to use 15mm axles - One pair required for each hub to be converted
- Axle adapters for CX/GX/MT/FB-1110 Elite Series front hubs - Available in standard QR, 12mm, 15mm, and 20mm thru-axle options - Material: Aly - Color: Blk
Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S700 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S700
Add an Alfine hub, cog, spokes, and a rim to this Shimano Internally Geared Hub Small Parts Kit, and you're ready to rock. - Alfine hubs are packaged without small parts and require this kit plus a cog - Nexus hubs are packaged with small parts and cogs and do not require an additional small parts kit - For 11-Speed Hub - Includes CJ-S700 Cassette Joint for Vertical Dropouts *Cassette joint does not fit Di2 Alfine hubs
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
DT Swiss tubeless-ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type setups. - Durable adhesive tape works as a rim tape and airseal
Page 1 of 2 Next page